Starlink Mini 3-Magnet Mount with Silicone Case, Gray or Black

$69.99

The Starlink Mini 3-Magnet Mount combines a fitted silicone case with three removable magnetic feet for suitable steel surfaces. Choose gray or black, then carry the Mini by its integrated handle or detachable, adjustable shoulder strap. Seven 1/4-20 threaded mounting points let you add compatible hardware separately.

Brand / ManufacturerSTARGEAR
Compatible DeviceStarlink Mini
Color OptionsGray or black
Case MaterialSilicone
Direct Mounting SurfaceSuitable flat magnetic steel
Magnetic Feet3 removable feet, 66 mm diameter each
Threaded Mounting Points7 × 1/4-20
Carrying OptionsIntegrated handle and detachable, adjustable shoulder strap
Included Components1 silicone case and mounting base with integrated handle, 3 magnetic feet and 1 shoulder strap
Unit Count1 kit
SKU: N/A Category: Brand:

Starlink Mini 3-Magnet Mount with a Silicone Case

The Starlink Mini 3-Magnet Mount combines a fitted silicone case and a removable three-foot magnetic setup for the Starlink Mini. Choose gray or black based on the case color you prefer.

The Starlink Mini silicone case fits around the dish and leaves its power port accessible. The handle, strap and storage lid help keep the setup together between stops.

Set It on Suitable Steel

Use the Starlink Mini 3-Magnet Mount on a clean, flat steel surface that attracts magnets. Check the actual panel before you place the dish or connect power.

Fit the three supplied magnetic feet to the mounting base as shown in the product instructions. All three feet should sit flat on the same surface.

Avoid seams, trim and curved sections that stop a foot from sitting flush. If the case rocks or a foot lifts, choose a different mounting spot.

For aluminum, glass or fiberglass, use a separately sold mounting system suited to that surface. Compatible steel contact plates are one option when the surface and plate instructions allow them.

Carry the Mini Between Stops

Lift the Starlink Mini carry case by its integrated handle, or clip on the adjustable shoulder strap before you carry the Mini. Check that the strap clips are fully closed before lifting.

The Starlink Mini 3-Magnet Mount has a lidded storage compartment that can hold the three magnetic feet when you remove them for transport. Route the Mini power cable through the case opening when it is set up.

Disconnect and pack the cable before lifting the case so it cannot pull on the port.

Add Compatible Hardware at the Threaded Points

The case has seven 1/4-20 threaded mounting points for compatible hardware. Check the thread and fit of your accessory before attaching it to the case.

The pictured clamp and suction cup setups show how the threaded points can be used. The kit includes the case and magnetic feet.

Those alternate mounts are sold separately.

Check the Fit Before Use

Seat the Mini in the silicone case, check that the feet make full contact and leave enough slack at the cable opening. Use the Starlink Mini 3-Magnet Mount while parked or docked.

Keep the case, handle and strap clear of doors, hatches and walkways when you set up the dish on an RV or boat. Stow the dish and mount before travel.

If you move the setup to a different vehicle or boat, check its mounting surface and cable route again.

Why You’ll Love It

  • Three removable magnetic feet for use on suitable steel.
  • Fitted silicone case available in gray or black.
  • Integrated handle and detachable, adjustable shoulder strap.
  • Lidded compartment for the magnetic feet between setups.
  • Seven 1/4-20 threaded mounting points for compatible hardware.Starlink Mini 3-Magnet Mount shown in gray with three magnetic feet and a case component diagram Gray case on a vehicle roof beside a rear view of the mounting base Gray mounting base with a 1/4-20 insert and separate clamp, magnetic and suction cup examples Three outdoor scenes showing the Mini carried by hand, shoulder strap and backpack Gray case handle and corner beside the open compartment holding three magnetic feet Exploded gray case assembly alongside a Starlink Mini fit diagram and other dish profiles Four illustrations showing the Mini on an RV, yacht, SUV and pickup

FAQ

Q1: What else do I need to use this kit?

A1: The Starlink Mini 3-Magnet Mount includes the case, three magnetic feet and shoulder strap. Bring your own Starlink Mini, power cable and power source.

Q2: Will the feet stick directly to an aluminum or glass roof?

A2: The feet attach directly to suitable magnetic steel. For aluminum or glass, choose compatible contact plates or a mounting system rated for that surface.

Q3: Is this the same as a four-magnet mount?

A3: This kit uses three removable magnetic feet. Check the product name, color and kit contents when comparing it with other STARGEAR mounts.

Q4: Are a clamp and suction cup mount in the box?

A4: The Starlink Mini 3-Magnet Mount includes the silicone case and magnetic setup. The clamp and suction cup in the illustrations are separate hardware.

Q5: Can I use it on an RV or boat?

A5: Yes, while parked or docked, with a flat, suitable magnetic steel mounting surface. Check that all three feet sit flat before using the dish.

Color

Grey, Black

Reviews

There are no reviews yet.

Be the first to review “Starlink Mini 3-Magnet Mount with Silicone Case, Gray or Black”

Your email address will not be published. Required fields are marked *

Secure Payments
Secure Payments. Encrypted & Protected.
Worldwide Shipping
Shipping to 200+ Countries & Regions.
Gifts & Sales
Curated Gifts for Every Occasion.
24/7 Support
Live Support via Chat, Email, or Phone.

Starlink Mini case shown on a vehicle roof with front and rear views and three round magnetic feet
Starlink Mini 3-Magnet Mount with Silicone Case, Gray or Black

$69.99

Select options This product has multiple variants. The options may be chosen on the product page